Liebert iCOM Microprocessor TM-10098 Manuel d'utilisateur Page 42
- Page / 170
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
iCOM
Control Training and Service Manual
Freecooling and Dual cooling will operate in the same manner as chilled water
with the supervision of the Supply Limit, again showing different valve positions on
the units
If in a Freecooling or Dual Cooling unit if the limit of the coil operation is detected
(no free cooling or no CW available) the valve will close off and unit will become
DX operation in the system.
Networking and Functions
Unit 2 Unit (U2U) Communications by networking will allow the following
functions to be placed into operation when the requirements exist. The user
must install the correct hardware and properly program the units for the
functionality.
In the iCOM Network the owner may perform the following functions:
The Teamwork Mode functions, which allow multiple stages of Cooling/ Heating
and/ or Humidification/ Dehumidification. The ability to prevent the units fighting is
included in this feature.
The Lead/ Lag function, which allows one or more units to be set as “Running and
Standby” for activation in case of an alarm. This also has the ability to be
programmed in a rotation for assurance of functional standbys.
The Cascade function, which allows additional units to be staged on based on the
temperature or humidity requirement.
Understanding the iCOM Network setup process:
To setup a system network with the iCOM control requires a complete
understanding of the control processes and parameter programming to insure the
proper functional operation without incident. To insure the setup is correct and
that the operation will function as selected you need to map both the room layout
and the unit setup. First, read and record all programmed settings in all of the
single units. Second, document the network parameter settings that are needed
and identify the numerical order of the units to be networked. The order of the
setup process is very important.
41
- Large Systems 1
- Training & Service 2
- Table of Contents 4
- Chapter 1 7
- Temperature and Humidity 7
- Control Programs 7
- Proportional (P) Control 9
- Temperature Control 12
- Staged Electric Reheat 22
- Humidity Control 25
- Operations and Charts 27
- Humidifier Operation 27
- Dehumidification Operation 31
- Systems 31
- Caution: 35
- Additional Programs 36
- Next Maintenance Calculation 39
- Networking and Functions 42
- The Basics for Hardware: 43
- Setting Parameters 45
- Unit No. 1 46
- Unit No. 2 46
- Teamwork 49
- Teamwork Mode 2 50
- Standby & Cascade 51
- Chapter 2 53
- Icon Key Name Function 55
- Programming Functions 57
- Menu Screens ICON Symbols 58
- Menu Parameters Names 58
- Icon Name Descriptions 59
- Available 59
- Display 59
- Menu Parameters 61
- Service Menu Parameters 68
- Advanced Menu Parameters 85
- Chapter 3 101
- LCD Display Board 102
- Unit Mounted Control Board 103
- DS Systems: 108
- Fuse Board Layout: All Units 112
- Chapter 4 115
- Isolation 116
- BASIC OPERATION OF THE TRIAC 117
- Moisture Content Charts 127
- NTC (Code S606 and S608) 145
- Troubleshooting Checklist 147
- User Menu 148
- Service Menu 150
- Advanced Menu 155
- Glossary of Terms 157
- Computer and Network Terms 161
- The industry has 164
- Network Information 166
- 192.168.168.1 167
- How To Use The Schematics 168
- Electrical Schematics 169
Alto-Shaam ED2SYS-96 manuals
Owner’s manuals and user’s guides for Unknown Alto-Shaam ED2SYS-96.
We providing 1 pdf manuals Alto-Shaam ED2SYS-96 for download free by document types: User Manual
Commentaires sur ces manuels