Liebert D42CIS7018 Manuel d'utilisateur Page 15
- Page / 36
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installation
11
3.7.1 Remove the Door
1. Open the door and swing it open about 90 degrees.
2. Lift the door slightly until the hinge pins clear the hinge pin caps and slide the door free (see
Figure 8).
Figure 8 Door hinge removal
3.7.2 Reverse the Door
1. Determine the correct location for the hinge pin assemblies, both top and bottom.
2. Mark the corresponding new position on the opposite side of the Knurr DCM. The frame is tapped
for proper hinge placement.
3. Lift the door off the Knurr DCM.
4. Take out the screws to remove the hinge pin assemblies; each assembly is attached with two
screws.
5. Attach the hinge pin assemblies in the new locations on the opposite side.
6. Remove the pin and reinstall it on the opposite hole. (When the door is reversed, the pin will be
pointing down.)
7. Extract the screw holding the hinge pin cap in place.
8. Flip the Hinge Pin Cap and insert it in the other end of the hinge on the door (see Figure 8).
9. Insert and tighten the screw holding the Hinge Pin Cap in the hinge.
10. Repeat Steps 7 through 9 for the other hinge.
11. Flip the door, and slide it into place.
12. Remove the unit badges from the front of the door and reattach them near what is now the top of
the door.
3.7.3 Reverse the Door Handle
After the door has been reversed, the door handle of the Knurr DCM will operate without adjustment,
but it will be upside down. To reverse the handle, follow these steps:
1. Open the door and remove all the bolts holding the door handle and lock assembly, including the
four brackets. Studs and nuts secure the brackets to the door frame.
2. Flip the door handle and lock assembly 180 degrees and reattach it with the bolts and nuts.
3. Check the handle and lock to ensure they operate properly.
Hinge is on the Knurr DCM door. Lift the
door until the hinge pins at the top and
bottom clear and slide the door free. The
door is held in place by gravity.
Door Hinge
Hinge Pin
Torx head screws hold
the hinge pin assembly
to the Knurr DCM frame
Hinge Pin Cap (rests on hinge pin)
Door Hinge
Move the Hinge Pin Cap here
when changing the way the
door swings; a screw fits
through the hole to secure
the Hinge Pin Cap
Door
Knurr DCM frame
- User Manual 1
- SAVE THESE INSTRUCTIONS 2
- TABLE OF CONTENTS 3
- 1.0 INTRODUCTION 5
- 2.0 MAJOR COMPONENTS 6
- 2.3 Mounting Hardware 7
- 3.0 INSTALLATION 8
- 3.3 Unloading the Knurr DCM 9
- 3.4 Equipment Layout 9
- Installation 10
- 3.6.1 Internal Mounting Rails 11
- 3.7 Door—Remove and Reverse 14
- 3.7.1 Remove the Door 15
- 3.7.2 Reverse the Door 15
- 3.7.3 Reverse the Door Handle 15
- 3.8.1 Remove a Panel 16
- 3.8.2 Replace a Side Panel 16
- 4.0 OPTIONS—INSTALLATION 17
- Options—Installation 18
- 4.6 Install RPC 22
- Mounting Brackets 22
- 4.7 Tool-Less Blanking Panels 23
- 4.8 Cluster Configuration 24
- 4.9 Cable Management 25
- OF CABINET 26
- 4.11.2 1U Cable Routing Panel 28
- 5.0 MAINTENANCE 31
- 6.0 SPECIFICATIONS 32
- DC6111—2A 32
- 7.0 ACCESSORIES 33
- Accessories 34
- SL-11384_REV0_01-11 36
Brother HL-5350DN manuels
Manuels d'utilisation et guides de l'utilisateur pour Imprimantes laser/LED Brother HL-5350DN.
Nous fournissons des manuels en pdf 1 Brother HL-5350DN à télécharger gratuitement par type de document : Fiche technique
Commentaires sur ces manuels